How To Repair A Delta Kitchen Sink Faucet

Download Article

Download Article

Considering they get heavy everyday utilise, bathroom sinks can easily go chipped, stained, or scratched over time. When this happens, you may want to install a new sink to raise the ambience of your bathroom and create a fresh, make clean look. While replacing a bathroom sink takes a flake of time, and replacing the faucet is a separate only essential element of the process, the overall job is manageable for almost DIYers.

1. 1

   Plow off the h2o supply and empty the lines. The shutoff valves are usually located in the cabinet under the sink. Turn both the hot and cold valves clockwise until they resist further turning. Then, plough on the hot and cold faucet taps to empty the faucet lines.^[1]

   • If the shutoff valves won't stop the flow of water completely, yous'll take to supervene upon them. Unless you have some plumbing feel, this may be a job all-time left to a professional.

2. 2

   Disconnect the P-trap portion of the drain pipe. If the P-trap is made of PVC, loosen the slip nut that connects it to the underside of the sink bleed by mitt. If the P-trap is fabricated of metal, loosen the connecting nut with channel locks.^[ii]

   • You don't need to remove the P-trap to replace the sink, but you may want to remove information technology temporarily then yous can articulate information technology of debris. To have it out, unscrew the nut (by mitt or with channel locks) that connects the lesser of the P-trap to the drain line below.
   • Place a bucket or heavy towel at the lesser of the cabinet to catch any dripping h2o.

   Ad

3. iii

   Unfasten the hot and common cold h2o lines with a crescent wrench. These are flexible lines that run from the shutoff valves to the underside of the faucet. Disconnect them correct above the shutoff valves. Some types may have basics y'all can loosen by hand, but y'all'll oft have to apply a crescent wrench.^[3]

   • You lot tin reuse these water lines if you want—just disconnect them from the underside of the sink subsequently, then reattach them during installation. But this is as well a proficient time to supervene upon them.

4. 4

   Measure the dimensions of the one-time bathroom sink with a measuring tape. If you lot want to reuse your existing countertop, makes sure you get a new sink that will fit in the same spot equally the one-time i. Write down the length, depth, and width of the sink, every bit well equally the length and width of the countertop.^[four]

   • You'll likely take to replace the countertop as well if you want a new sink that's a different size.

5. 5

   Buy your new sink at a domicile comeback store. Bring the measurements of the sometime sink and countertop with you. This helps to ensure y'all purchase the correct size before putting in a bathroom sink. Brand sure the replacement sink is the same type (top-mount or undermount) as the old ane!^[5]

   • Enquire an employee for aid if you need assist selecting a new sink.
   • Make sure the new sink's drain lines upwardly with your sometime drain line, or else you lot'll have to rework the plumbing.^[vi]
   • Nearly bath sinks are nonetheless made of ceramic, only there are other options, and many colors to choose from beyond the traditional white.

   Advertisement

1. 1

   Remove the clips under the sink that hold information technology against the countertop. Many, merely not all, sinks have clips underneath them that create a pressure connection against the underside of the counter. If your sink has them, loosen them either by hand or with a screwdriver.^[7]

   • If your new sink requires clips, it should come with them. However, yous may desire to keep these old ones for the time existence, but in case they might come in handy.

2. 2

   Cut any sealant between the sink and the countertop with a utility knife. Advisedly run the blade of the knife between the rim of the sink and the countertop.^[viii] Doing then will slice through the caulk or other sealant that secures the sink and countertop together.^[9]

   • Work slowly and carefully so you don't cut into the countertop, specially if it'south made of laminated wood. Of course, if you're replacing the countertop as well, you lot tin can be equally messy equally you lot like!

3. 3

   Lift out the onetime sink from the counter. If y'all tin can get a expert grip from above, you can elevator it straight upwards and out. Otherwise, have a second person push button up from below, then lift out the sink when information technology pops up.^[10]

   • If you have a cast-iron sink, have someone else help you elevator it since it could exist pretty heavy.^[xi]
   • In one case the old sink is out of the style, scrape abroad whatever residuum caulk or sealant on the countertop. Apply a plastic putty knife for scraping, then clean upwards any residue with a rag dipped in mineral spirits.

4. 4

   Install the faucet and drain on the new sink. You can either remove the faucet and drain from the erstwhile sink and reuse them, or purchase a new faucet and bleed to become with your new sink. If you are non experienced with this type of project, you may be better off with a new faucet and drain, since they will come with detailed installation instructions.^[12]

   • Faucet and drain installations will vary quite a bit based on the particular make and model you lot select. However, with a skillful set of instructions, information technology is a project about DIYers tin handle. Otherwise, contact a plumber.

5. 5

   Use silicone caulk to the underside of the new sink's rim. Clasp a steady strip of caulk all the style around the underside of the rim. This will hold the sink in identify and prevent water from dripping down into the cabinet.^[xiii]

   • Choose a silicone caulk intended for use with bathroom fixtures. Don't utilise acrylic or other non-silicone caulks.

6. half dozen

   Lower the sink into the hole in the countertop. Lift the sink carefully and slowly drop it straight down into the opening. Once it'due south in place, push down on the sink and wipe off whatever excess silicone that squeezes out with paper towels.^[14]

   • This task may exist a scrap easier if you have a second person achieve up from within the cabinet to support the sink from below.

7. 7

   Attach the sink to the underside of the counter with fastener clips. Follow the instructions that come with your new sink regarding the placement of the clips. Either tighten them by hand or with a screwdriver, equally indicated by the instructions. Once secured, they'll apply force per unit area to hold the sink tight to the underside of the counter.^[15]

   • Not all sinks require clips for installation. If your model does utilise clips, they should come up in the package with your new sink. If you're missing a clip or two, it's possible that the clips from your one-time sink may work.

8. eight

   Run a bead of caulk effectually the rim of the sink where it meets the countertop. Your goal here is to create a waterproof barrier between the rim of the sink and the countertop so that h2o can't seep in under the sink rim. Once you've run the bead of caulk around the sink rim, wet your index finger and run it around the entire dewdrop to shine the caulk in identify. Then use clammy paper towels to wipe away any backlog.^[16]

   • Apply the same silicone caulk you used to attach the underside of the sink to the countertop.

   Ad

1. 1

   Cut through the caulk that connects the sink to the underside of the counter. Attain into the sink from above and run the bract of a utility knife through the bead of caulk, all the way around the rim of the sink. Work carefully so y'all don't scratch the lip of the opening in the countertop.^[17]

   • This caulk helps to hold the undermount sink in place but is primarily there to preclude water from getting between the sink rim and the underside of the counter.

2. 2

   Remove the holding clips under the sink while supporting it from below. Although it will exist a tight fit in the sink cabinet, this is safer and easier with a second set of hands helping you. While the second person holds the bottom of the sink, remove the several clips (often 4-half-dozen) that pin the sink rim against the underside of the counter. They will either be screwed or epoxied into place.^[18]

   • If they're attached with screws, simply use a screwdriver to remove them.
   • If they are stuck in place with epoxy, use a putty knife to scrape, pry, and wedge the clips apart from the underside of the counter.
   • Once you remove the clips, the sink will be free to autumn, and then make certain information technology's being held upward by someone!

3. 3

   Lower the sink down and out of the cabinet. At present that the caulk and the clips have been removed, simply guide the sink downwards and out of the cabinet. If you are reusing the existing faucet and drain, remove them now. But it's more likely that y'all'll desire to install new ones with your new sink.^[19]

4. 4

   Install the faucet , only non the drain, in the new sink. Unlike with a elevation-mount sink, don't install the drain before installing an undermount sink. Only it'south easier to install the new faucet at present instead of having to work from within the sink cabinet.^[20]

   • Installing a faucet is inside the skill set of nearly DIYers, but the process differs based on the blazon and model of faucet. Closely follow the instructions that come with the new faucet.

5. five

   Employ a bead of silicone caulk around the entire pinnacle rim of the sink. Employ a silicone caulk designed for bathroom applications. Make sure the dewdrop is continuous around the entire rim of the sink.^[21]

   • Similar the stuff you removed from the old sink, this caulk is mostly at that place for waterproofing, but also helps hold the sink in place.

6. 6

   Secure the sink in position with a piece of lumber and a bar clamp. Cut a section of 2 in × 4 in (5.1 cm × ten.ii cm) lumber and so information technology's at least a few inches/centimeters longer than the width of the opening for the sink in the countertop. Lay this piece of wood beyond the opening. Then, while a second person lifts the new sink up into place from beneath, feed the bar clench up through the bleed opening of the sink so that one of its clamps holds upward the sink from below. Secure the other clench to the piece of wood and tighten it.^[22]

   • Brand sure the clamp is tight enough to brand the some of the silicone caulk squeeze out betwixt the rim of the sink and the underside of the counter. Wipe away this excess caulk with a damp rag.

7. 7

   Secure the included clips in place with screws or epoxy. Your new undermount sink volition come up with support clips to identify around the underside of the sink where it meets the underside of the counter. In some cases, these clips may attach with screws. If and so, drill pilot holes and utilize a screwdriver to secure the clips in place. Otherwise, use the brand or type of epoxy recommended past the sink manufacturer.^[23]

   • In most cases, the clips are adhered in place with a 2-part epoxy that hardens in about 10 minutes after being combined. Follow the product instructions carefully and apply the proper amount to each prune. Then press them into place every bit per the installation instructions for your sink.

8. 8

   Expect 24 hours, so install the drain. Even though the epoxy should exist fully set in 10 minutes, it's important to give the silicone adhesive fourth dimension to cure fully. Leave the slice of lumber and bar clamp in place for a day before removing them. Subsequently that, you lot can put the drain in place and continue with the installation.^[24]

   • Like faucets, drain installations vary by type and brand, but the procedure is DIY-friendly if yous follow the instructions carefully.
   • You could rely on the epoxy to hold everything in place after 10 minutes and not wait the full 24 hours earlier proceeding, merely this is non recommended. Be patient!

   Advertising

1. ane

   Allow the caulk on a top-mount sink to cure for 24 hours. Instead of making the final connections right away, it's better to give the silicone caulk time to set up. This volition prevent the sink from shifting and breaking the solid bead of caulk that y'all fabricated.^[25]

   • If you're installing an undermount sink, y'all should already take waited 24 hours earlier putting in the sink drain. In this example, you tin can proceed with the last steps of the installation.

2. 2

   Reconnect the h2o lines and the P-trap underneath the sink. You merely demand to practise the contrary of the disconnecting procedure. Paw-tighten the water lines where they connect to the hot and cold shutoff valves or use a crescent wrench if needed. Similarly, employ your easily to tighten the nut on a PVC P-trap or channel locks for a metal P-trap.^[26]

   • If your new sink drain is a petty shorter than your sometime one, you can buy a P-trap pipe extension at your local hardware shop. The extension can be cutting to fit and will as well connect in place with a nut that y'all'll either mitt-tighten or secure with channel locks.
   • If your new sink bleed is a little also long, you tin can cut off some of the piping either at the elevation of the P-trap or the bottom of the drain. Utilize a hacksaw or piping cutter to make the aligning.

3. 3

   Plough the water back on and bank check for leaks. Open the hot and common cold water valves by turning them counterclockwise. So, open the hot and cold faucet taps fully and let the water run for at least 2-iii minutes. Watch under the cabinet for whatever leaks in the h2o lines, drain lines, or elsewhere. Tighten any loose connections as needed.^[27]

   • Keep the bucket or towel at the lesser of the sink cabinet while you test for leaks.
   • If you lot have a leak at a pipe connectedness, try shutting off the water, undoing the connexion, wrapping some plumber'south tape effectually the pipe threads, then re-making the connexion.
   • If yous can't figure out where a leak is coming from and/or how to fix information technology, shut off the water supply lines and call a plumber.

   Advert

Add New Question

• Question

  Can I replace a sink by myself?

  

  Allen Lee
  Home Improvement Specialist

  Allen Lee is a Dwelling Improvement Specialist and the Owner of Honest Lee Handyman Services, a licensed and insured handyman business concern servicing Sacramento, California, and surrounding areas. Working with homeowners and businesses to go their minor repairs done in a timely and efficient way, Honest Lee Handyman Services provides gutter and dryer vent cleaning along with fixture, fence, drywall, and toilet repairs.

  

  Abode Improvement Specialist

  Expert Respond

Ask a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Advertisement

Things You'll Need

• Measuring tape
• Pencil and newspaper
• New sink
• Channel lock pliers
• Crescent wrench
• Screwdriver
• Utility knife
• Silicone caulk
• Paper towels
• Fastener clips
• Plumber's record
• New faucet
• Piece of two in × four in (5.1 cm × ten.ii cm) lumber (for undermount sink)
• Bar clamp (for undermount sink)
• 2-part epoxy (for undermount sink)

Almost This Article

Article Summary 10

To supersede a meridian-mount bathroom sink, turn off the h2o supply and empty the faucet lines. Next, remove the clips underneath, cut away any sealant between the sink and countertop, and lift the sink away from the counter. Then, install the faucet and drain on the new sink and use silicone caulk to the underside of the new sink'south rim. Lift the sink and drop it down into the opening. Finally, attach the sink to the counter with clips and run a dewdrop of caulk around the rim to create a waterproof barrier. For tips on replacing an undermount sink, read on!

Did this summary aid you lot?

Thanks to all authors for creating a page that has been read 170,924 times.

Did this article help you lot?

Source: https://www.wikihow.com/Replace-a-Bathroom-Sink

Posted by: grafsaink1990.blogspot.com

Share this post